tag:blogger.com,1999:blog-860668590768454554.post3718178203562089623..comments2023-05-26T07:00:38.737-07:00Comments on Oleksiy Gayda's Blog: TechTip: Port-mirroring on Avaya ERS/Nortel Baystack 5xxx series using CLIUnknownnoreply@blogger.comBlogger8125tag:blogger.com,1999:blog-860668590768454554.post-37605381888845006602016-05-17T14:02:32.193-07:002016-05-17T14:02:32.193-07:00
I successfully loaded this configuration on 455...<br /><br /><br />I successfully loaded this configuration on 4550T switch:<br />port-mirroring mode ManytoOneRxTx monitor-port 48 mirror-ports 45-47 so yes it is possible.... After typing port-mirroring mode ManytoOneRxTx monitor-port 48 ?...the ONLY option that became available is mirror-ports...emphasis on the PORTSSSSS<br />Anonymoushttps://www.blogger.com/profile/01995665634768001055noreply@blogger.comtag:blogger.com,1999:blog-860668590768454554.post-60563515700795744552016-05-17T13:53:48.763-07:002016-05-17T13:53:48.763-07:00It appears that you can only make 1 session...I tr...It appears that you can only make 1 session...I tried making different sessions but everything I did gets replaced by the last one I created...so I think it is not possible... If you can make several sessions then it would be possible...Anonymoushttps://www.blogger.com/profile/01995665634768001055noreply@blogger.comtag:blogger.com,1999:blog-860668590768454554.post-51585306560164079582016-03-13T06:48:24.825-07:002016-03-13T06:48:24.825-07:00is there a way to sniff the same port (source) to ...is there a way to sniff the same port (source) to two diffrent sniffers (dest) on 5520 platform?<br />(this option should be called OneToMany)Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-860668590768454554.post-84525322400639643432015-09-28T14:02:44.487-07:002015-09-28T14:02:44.487-07:00It's been a while since I worked with this, an...It's been a while since I worked with this, and my initial response is that yes - you should be able to do it with the ManytoOneRxTx command ("ManytoOneRxTx monitor-port X mirror-ports Y, Z, W"). However, just doing some quick online searches for the syntax, it looks like it may depend on the switch model/firmware version - at least some of the documentation is suggesting that this command works with MAC addresses as opposed to port numbers ("ManytoOneRxTx monitor-port X mirror-MAC-A aaaa.bbbb.cccc"). Hope this helps.Oleksiy Gaydahttps://www.blogger.com/profile/14277525564994398372noreply@blogger.comtag:blogger.com,1999:blog-860668590768454554.post-69633846391100435032015-09-28T08:27:34.044-07:002015-09-28T08:27:34.044-07:00Can you mirror multiple ports (more than 2) as sou...Can you mirror multiple ports (more than 2) as source to one destination port where you have your sniffer? would this do it: ManytoOneRxTx (any to one port mirroring ingress & egress traffic)Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-860668590768454554.post-22366660425879128542014-10-28T00:23:43.715-07:002014-10-28T00:23:43.715-07:00thanks very good..thanks very good..Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-860668590768454554.post-39322742594580472072014-10-19T05:30:24.453-07:002014-10-19T05:30:24.453-07:00thank you
very good Explanationthank you <br />very good ExplanationAnonymousnoreply@blogger.comtag:blogger.com,1999:blog-860668590768454554.post-86439110599053032132013-09-06T09:40:33.111-07:002013-09-06T09:40:33.111-07:00Excellent in both scope and presentation. Very eas...Excellent in both scope and presentation. Very easy to understandAnonymousnoreply@blogger.com